How To Fix Convertible Back Window

Download Commodity

Download Article

Modern soft convertible motorcar tops often have glass windows glued to the cloth, vinyl or other soft material with a melted plastic strip instead of a clear vinyl window sewn to it. If and when the glass comes unstuck -- sometimes due to the canvass shrinking from neglect or otherwise -- it can be very hard to reattach. Double-sided foam tape such as 3M VHB record (what i author used, others could exist OK too) tin reattach them, but should be applied in a specific fashion to avert abiding strain that will break its bond.

Steps

1. i

   Reattach the soft meridian material ("sheet") to the glass when just part of the canvas has discrete and then that the glass does not have to exist re-centered within the hole in the canvas. If it does accept to exist re-centered one might do that past measuring distances with the defrosting grid as a guide and, in any case, belongings the glass temporarily in identify with gaffer's or other sticky tape.

2. 2

   Open the acme slightly and then that it is not taut. Prop something such as a small empty box between the front edge of the top and the upper edge of the windshield frame so that the meridian stays open slightly.

   Advertisement

3. iii

   Notice the seal that was attached but has get unattached, such equally the lower edge of the exterior layer of canvas. ^[1] If clay has accumulated in the pocket that has been exposed to the weather yous may wish to vacuum out any large particles.

4. 4

   If merely a very pocket-size part has separated leave information technology lone. If a large part is by and large separated yous may wish to separate it entirely to re-seal it as one continuous piece.^[2]

5. 5

   Clean the mating surfaces with rubbing booze.

6. half dozen

   Close the roof completely to see where the canvas falls on the drinking glass when pulled gently apartment as far in on the glass as it volition go, but not pulled hard. At to the lowest degree in the case of cotton canvas, this will probably exist not as far upward onto the drinking glass as originally (or equally on a however-attached inside layer) because it will have shrunk since new.

7. 7

   Re-open the roof slightly and re-prop information technology.

8. 8

   Apply a strip of double-sided foam tape such as 3M VHB ("very high bail")--cream so that it volition arrange to any irregularities, preferably black so ultraviolet rays volition not promptly destroy its exposed edge--to the glass with the edge coming upwardly to the point you determined previously. ^[3]

9. 9

   Bring the center of the area being attached (such as the center, left-versus-correct-wise of the bottom exterior canvas) up to the edge of the tape. Information technology should have but a little slack, since it needs to be pulled basically smooth simply not taut when the peak is closed. Just a petty slack when the superlative is airtight is much improve than tension, which volition unstick the tape.

10. 10

    Stick the sheet to the tape, working outward. The reason to work outward from a central point is so that whatsoever "excess" material does non build up at one side.^[4]

11. 11

    Rub down the sheet over the record firmly and apply some estrus--non a great painfully hot corporeality--with a accident dryer for a thorough bond.

    • The convertible top should exist stock-still.

Advertisement

Add New Question

• Question

  How much will it cost to replace the top with the original window?

  

  I take a 2007 Mustang convertible. The window is separating from the textile height. I went to 2 convertible top/upholstery shops, and both told me the window is heat sealed and the entire top needed to be replaced, and both gave me a price of $1,900.

• Question

  I take in my garage a Corvette convertible with a canvas top in smashing status. The seal effectually the drinking glass rear window has popped, will this process work?

  

  I used 3M window weld on our 2004 Volvo C70 top and it worked great! Make sure you get as much of the sometime adhesive off as possible. Put the 3M primer on first and let it dry for nigh 10 minutes. Put a bead (most 3/sixteen) of window weld on it. Clamp information technology in place. I used some paint stirrer sticks & C clamps. Let it sit for almost 24 hours. Do not do this if temperature is below 40 degrees F.

• Question

  Where can I get 3M VHB foam tape?

  

  Amazon has it in a variety of lengths and widths.

• Question

  Tin can Gorilla mucilage be used to attach glass to a convertible canvas superlative?

  

  No. I tried it and the heat from sitting in the sun made it scissure and come apart.

• Question

  How much will information technology cost to replace a rear window on a convertible Sebring?

  

  The shops will tell you lot a new pinnacle is needed. Fortunately, the Sebring window lays on summit of the canvas flap rather than hanging from it. People swear by Rhinoceros mucilage for about twenty bucks. I'yard planning to remove the window, make clean the entire lip that the window edge contacts, put a dewdrop of rhino on information technology and lay the window back in. Removing information technology completely will let me to position information technology evenly in the hole since the top textile has most likely shrunk over the years only if yours is only pulling autonomously in a section you tin can open the superlative part mode and gum the lip while tension is off.

• Question

  Should I glue the inside and the exterior of the window?

  

  Brett Gilbert

  Top Answerer

  Yes, if the canvas is loose on the within part of the window, mucilage it as well.

• Question

  Where can I find instructions that are more than specific to the blazon of car I have?

  

  Brett Gilbert

  Tiptop Answerer

  Yous could contact the manufacturer or a mechanic to see what they recommend. Usually, though, they volition tell yous to replace the entire hood. The glue or tape techniques work well for simply about any car.

Ask a Question

200 characters left

Include your email address to go a message when this question is answered.

Submit

Advertisement

• It may exist better to get the acme fixed in a mode for whose possible failure someone else such as a dealer will take responsibility. But this is a nifty alternative to replacing the elevation.

Ad

Things You'll Demand

• 3M VHB foam tape, black

Well-nigh This Article

Thanks to all authors for creating a page that has been read 206,030 times.

Did this article help you?

Source: https://www.wikihow.com/Reattach-Rear-Window-Glass-to-a-Convertible-Car-Top

Posted by: goodssupostabothe.blogspot.com

Share this post